Shop Calculators
Free tools for the shop floor: speeds and feeds for Majac Mills end mills, and the right drill for every tap.
Tap drill size selector
Drill sizes are calculated for 75% thread (cut taps) and 65% thread (form taps), the usual starting points. Tougher materials may need less thread; check your tap maker's chart for critical work.
Results are starting points. Optimum speeds and feeds depend on material, setup, machine condition and tool deflection. Need help with a tough job? Call +1 705 728 8665. Full charts for every series are below.
Majac Mills speeds & feeds charts
Recommended starting points for every series (2026 edition).
General Purpose
| Material | SFM Uncoated | SFM TiAlN | 1/4" | 5/16" | 3/8" | 7/16" | 1/2" | 5/8" | 3/4" | 1" |
|---|---|---|---|---|---|---|---|---|---|---|
| Feed per tooth (IPT) by diameter | ||||||||||
| Non-ferrous (N) | ||||||||||
| Aluminum & Aluminum Alloys | 600–1200 | 900–1800 | .0020 | .0025 | .0030 | .0035 | .0040 | .0050 | .0060 | .0080 |
| Copper & Copper Alloys | 350–850 | 525–1275 | .0020 | .0025 | .0025 | .0030 | .0030 | .0035 | .0040 | .0060 |
| Brass & Bronze | 250–400 | 375–600 | .0020 | .0025 | .0025 | .0030 | .0030 | .0035 | .0040 | .0050 |
| Graphite | 500–800 | 500–1200 | .0030 | .0035 | .0025 | .0030 | .0030 | .0040 | .0050 | .0070 |
| Plastics | 600–1100 | 600–1650 | .0030 | .0035 | .0040 | .0050 | .0060 | .0080 | .0100 | .0150 |
| Cast iron (K) | ||||||||||
| Cast Iron (soft) | 250–450 | 375–650 | .0020 | .0022 | .0025 | .0027 | .0030 | .0045 | .0060 | .0080 |
| Cast Iron (hard) | 100–250 | 100–375 | .0008 | .0010 | .0015 | .0017 | .0020 | .0025 | .0030 | .0040 |
| Ductile Iron | 80–400 | 100–600 | .0010 | .0012 | .0015 | .0017 | .0020 | .0030 | .0040 | .0060 |
| Malleable Iron | 150–500 | 225–650 | .0010 | .0015 | .0020 | .0025 | .0030 | .0040 | .0050 | .0070 |
| Steels (P) | ||||||||||
| Low Carbon Steels | 200–400 | 300–600 | .0010 | .0015 | .0020 | .0025 | .0030 | .0040 | .0050 | .0070 |
| Medium Carbon Steels | 100–250 | 150–375 | .0015 | .0016 | .0017 | .0018 | .0020 | .0030 | .0040 | .0050 |
| Steels Hardened to 35 Rc | 130–230 | 130–345 | .0010 | .0011 | .0012 | .0013 | .0015 | .0017 | .0020 | .0030 |
| Steels Hardened to 50 Rc | 70–130 | 70–160 | .0007 | .0007 | .0008 | .0009 | .0010 | .0015 | .0020 | .0030 |
| Steels Hardened to 60 Rc | 30–70 | 30–90 | .0005 | .0006 | .0007 | .0009 | .0010 | .0012 | .0015 | .0020 |
| Mold Steels | 200–350 | 300–525 | .0010 | .0012 | .0015 | .0017 | .0020 | .0025 | .0030 | .0040 |
| Tool Steels | 100–250 | 150–375 | .0010 | .0012 | .0015 | .0017 | .0020 | .0025 | .0030 | .0040 |
| Stainless (M) | ||||||||||
| Stainless Steels (soft) | 200–350 | 300–450 | .0010 | .0012 | .0015 | .0012 | .0020 | .0030 | .0040 | .0060 |
| Stainless Steels (hard) | 100–200 | 150–300 | .0005 | .0006 | .0007 | .0008 | .0010 | .0020 | .0030 | .0050 |
| Super alloys (S) | ||||||||||
| Monel & High Nickel Steel | 75–175 | 75–200 | .0010 | .0012 | .0015 | .0017 | .0020 | .0025 | .0030 | .0040 |
| Titanium (soft) | 125–300 | 125–375 | .0010 | .0012 | .0015 | .0017 | .0020 | .0030 | .0040 | .0060 |
| Titanium (hard) | 50–150 | 50–175 | .0005 | .0006 | .0007 | .0008 | .0010 | .0015 | .0020 | .0020 |
| Nickel-Based High Temp Alloys | 50–100 | 50–125 | .0008 | .0008 | .0009 | .0009 | .0010 | .0012 | .0015 | .0020 |
Depth of cut up to 1× diameter for profiling and 0.5× diameter for full slotting. If the tool runs well without vibration or noise, increase SFM and/or feed per tooth in 5–10% steps.
High Performance
| Material | SFM TiAlN | 1/4" | 5/16" | 3/8" | 7/16" | 1/2" | 5/8" | 3/4" | 1" |
|---|---|---|---|---|---|---|---|---|---|
| Feed per tooth (IPT) by diameter | |||||||||
| Non-ferrous (N) | |||||||||
| Aluminum & Aluminum Alloys | 900–1800 | .0025 | .0030 | .0035 | .0040 | .0045 | .0055 | .0065 | .0085 |
| Copper & Copper Alloys | 525–1275 | .0025 | .0030 | .0030 | .0035 | .0035 | .0040 | .0045 | .0065 |
| Brass & Bronze | 375–600 | .0025 | .0030 | .0030 | .0035 | .0035 | .0040 | .0045 | .0055 |
| Cast iron (K) | |||||||||
| Cast Iron (soft) | 375–650 | .0025 | .0027 | .0030 | .0032 | .0035 | .0040 | .0065 | .0085 |
| Cast Iron (hard) | 100–375 | .0013 | .0015 | .0020 | .0022 | .0025 | .0030 | .0035 | .0045 |
| Ductile Iron | 100–600 | .0015 | .0017 | .0020 | .0022 | .0025 | .0035 | .0045 | .0065 |
| Malleable Iron | 225–650 | .0015 | .0020 | .0025 | .0030 | .0035 | .0045 | .0055 | .0075 |
| Steels (P) | |||||||||
| Low Carbon Steels | 300–600 | .0015 | .0020 | .0025 | .0030 | .0035 | .0045 | .0055 | .0075 |
| Medium Carbon Steels | 150–375 | .0020 | .0021 | .0022 | .0023 | .0025 | .0035 | .0045 | .0055 |
| Steels Hardened to 35 Rc | 130–345 | .0015 | .0016 | .0017 | .0018 | .0020 | .0022 | .0025 | .0035 |
| Steels Hardened to 50 Rc | 70–160 | .0012 | .0012 | .0013 | .0014 | .0015 | .0020 | .0025 | .0035 |
| Mold Steels | 300–525 | .0015 | .0017 | .0020 | .0022 | .0025 | .0030 | .0035 | .0045 |
| Tool Steels | 150–375 | .0015 | .0017 | .0020 | .0022 | .0025 | .0030 | .0035 | .0045 |
| Stainless (M) | |||||||||
| Stainless Steels (soft) | 300–450 | .0015 | .0017 | .0020 | .0017 | .0025 | .0035 | .0045 | .0065 |
| Stainless Steels (hard) | 150–300 | .0010 | .0011 | .0012 | .0013 | .0015 | .0025 | .0035 | .0055 |
| Super alloys (S) | |||||||||
| Monel & High Nickel Steel | 75–200 | .0015 | .0017 | .0020 | .0021 | .0025 | .0030 | .0035 | .0045 |
| Titanium (soft) | 125–375 | .0015 | .0017 | .0020 | .0021 | .0025 | .0035 | .0045 | .0065 |
| Titanium (hard) | 50–175 | .0010 | .0011 | .0012 | .0012 | .0014 | .0017 | .0022 | .0023 |
| Nickel-Based High Temp Alloys | 50–125 | .0013 | .0012 | .0011 | .0011 | .0014 | .0015 | .0017 | .0023 |
Depth of cut up to 1.25× diameter for profiling and 0.75× diameter for full slotting. If the tool runs well without vibration or noise, increase SFM and/or feed per tooth in 5–10% steps.
Ultra High Performance
| Material | SFM TiAlN | 1/4" | 5/16" | 3/8" | 7/16" | 1/2" | 5/8" | 3/4" | 1" |
|---|---|---|---|---|---|---|---|---|---|
| Feed per tooth (IPT) by diameter | |||||||||
| Non-ferrous (N) | |||||||||
| Aluminum & Aluminum Alloys | 900–1800 | .0025 | .0030 | .0035 | .0040 | .0045 | .0055 | .0065 | .0085 |
| Copper & Copper Alloys | 525–1275 | .0025 | .0030 | .0030 | .0035 | .0035 | .0040 | .0045 | .0065 |
| Brass & Bronze | 375–600 | .0025 | .0030 | .0030 | .0035 | .0035 | .0040 | .0045 | .0055 |
| Cast iron (K) | |||||||||
| Cast Iron (soft) | 375–650 | .0030 | .0032 | .0035 | .0037 | .0040 | .0045 | .0070 | .0090 |
| Cast Iron (hard) | 100–375 | .0018 | .0020 | .0025 | .0027 | .0030 | .0035 | .0040 | .0050 |
| Ductile Iron | 100–600 | .0020 | .0022 | .0025 | .0027 | .0030 | .0040 | .0050 | .0070 |
| Malleable Iron | 225–650 | .0020 | .0025 | .0030 | .0035 | .0040 | .0050 | .0060 | .0080 |
| Steels (P) | |||||||||
| Low Carbon Steels | 300–600 | .0020 | .0025 | .0030 | .0035 | .0040 | .0050 | .0060 | .0080 |
| Medium Carbon Steels | 150–375 | .0025 | .0026 | .0027 | .0028 | .0030 | .0040 | .0050 | .0060 |
| Steels Hardened to 35 Rc | 130–345 | .0020 | .0021 | .0022 | .0023 | .0025 | .0027 | .0030 | .0040 |
| Steels Hardened to 50 Rc | 70–160 | .0012 | .0012 | .0013 | .0014 | .0015 | .0026 | .0030 | .0035 |
| Mold Steels | 300–525 | .0020 | .0022 | .0025 | .0027 | .0030 | .0035 | .0040 | .0050 |
| Tool Steels | 150–375 | .0020 | .0022 | .0025 | .0027 | .0030 | .0035 | .0040 | .0050 |
| Stainless (M) | |||||||||
| Stainless Steels (soft) | 300–450 | .0020 | .0022 | .0025 | .0022 | .0030 | .0040 | .0050 | .0070 |
| Stainless Steels (hard) | 150–300 | .0015 | .0016 | .0017 | .0018 | .0020 | .0030 | .0040 | .0060 |
| Super alloys (S) | |||||||||
| Monel & High Nickel Steel | 75–200 | .0015 | .0022 | .0025 | .0027 | .0030 | .0035 | .0040 | .0050 |
| Titanium (soft) | 125–375 | .0015 | .0022 | .0025 | .0027 | .0030 | .0040 | .0050 | .0070 |
| Titanium (hard) | 50–175 | .0010 | .0016 | .0017 | .0018 | .0020 | .0022 | .0026 | .0030 |
| Nickel-Based High Temp Alloys | 50–125 | .0014 | .0014 | .0015 | .0016 | .0017 | .0018 | .0020 | .0023 |
Depth of cut up to 1.25× diameter for profiling and 0.75× diameter for full slotting. If the tool runs well without vibration or noise, increase SFM and/or feed per tooth in 5–10% steps.
HEM (High Efficiency Milling)
| Material | SFM ALL4 | 1/4" | 5/16" | 3/8" | 7/16" | 1/2" | 5/8" | 3/4" | 1" |
|---|---|---|---|---|---|---|---|---|---|
| Feed per tooth (IPT) by diameter | |||||||||
| Non-ferrous (N) | |||||||||
| Aluminum & Aluminum Alloys | 900–1800 | .0025 | .0030 | .0035 | .0040 | .0045 | .0055 | .0065 | .0085 |
| Copper & Copper Alloys | 525–1275 | .0025 | .0030 | .0030 | .0035 | .0035 | .0040 | .0045 | .0065 |
| Brass & Bronze | 375–900 | .0025 | .0030 | .0030 | .0035 | .0035 | .0040 | .0045 | .0055 |
| Cast iron (K) | |||||||||
| Cast Iron (soft) | 375–950 | .0030 | .0032 | .0035 | .0037 | .0040 | .0045 | .0070 | .0090 |
| Cast Iron (hard) | 150–475 | .0018 | .0020 | .0025 | .0027 | .0030 | .0035 | .0040 | .0050 |
| Ductile Iron | 200–900 | .0020 | .0022 | .0025 | .0027 | .0030 | .0040 | .0050 | .0070 |
| Malleable Iron | 275–850 | .0020 | .0025 | .0030 | .0035 | .0040 | .0050 | .0060 | .0080 |
| Steels (P) | |||||||||
| Low Carbon Steels | 350–900 | .0020 | .0025 | .0030 | .0035 | .0040 | .0050 | .0060 | .0080 |
| Medium Carbon Steels | 200–675 | .0025 | .0026 | .0027 | .0028 | .0030 | .0040 | .0050 | .0060 |
| Steels Hardened to 35 Rc | 190–545 | .0020 | .0021 | .0022 | .0023 | .0025 | .0027 | .0030 | .0040 |
| Steels Hardened to 50 Rc | 90–275 | .0012 | .0012 | .0013 | .0014 | .0015 | .0026 | .0030 | .0035 |
| Mold Steels | 300–725 | .0020 | .0022 | .0025 | .0027 | .0030 | .0035 | .0040 | .0050 |
| Tool Steels | 175–525 | .0020 | .0022 | .0025 | .0027 | .0030 | .0035 | .0040 | .0050 |
| Stainless (M) | |||||||||
| Stainless Steels (soft) | 300–525 | .0020 | .0022 | .0025 | .0022 | .0030 | .0040 | .0050 | .0070 |
| Stainless Steels (hard) | 150–475 | .0015 | .0016 | .0017 | .0018 | .0020 | .0030 | .0040 | .0060 |
| Super alloys (S) | |||||||||
| Monel & High Nickel Steel | 75–250 | .0015 | .0022 | .0025 | .0027 | .0030 | .0035 | .0040 | .0050 |
| Titanium (soft) | 125–475 | .0015 | .0022 | .0025 | .0027 | .0030 | .0040 | .0050 | .0070 |
| Titanium (hard) | 50–195 | .0010 | .0016 | .0017 | .0018 | .0020 | .0022 | .0026 | .0030 |
| Nickel-Based High Temp Alloys | 50–175 | .0014 | .0014 | .0015 | .0016 | .0017 | .0018 | .0020 | .0023 |
For HEM toolpaths the chip load must be adjusted for radial chip thinning; enter your radial width of cut. If the tool runs well without vibration or noise, increase SFM and/or feed per tooth in 5–10% steps.
HTAS (High Temp Alloy & Stainless)
| Material | SFM ALL4 | 1/4" | 5/16" | 3/8" | 7/16" | 1/2" | 5/8" | 3/4" | 1" |
|---|---|---|---|---|---|---|---|---|---|
| Feed per tooth (IPT) by diameter | |||||||||
| Non-ferrous (N) | |||||||||
| Aluminum & Aluminum Alloys | 900–1800 | .0025 | .0030 | .0035 | .0040 | .0045 | .0055 | .0065 | .0085 |
| Copper & Copper Alloys | 525–1275 | .0025 | .0030 | .0030 | .0035 | .0035 | .0040 | .0045 | .0065 |
| Brass & Bronze | 375–900 | .0025 | .0030 | .0030 | .0035 | .0035 | .0040 | .0045 | .0055 |
| Cast iron (K) | |||||||||
| Cast Iron (soft) | 375–950 | .0030 | .0032 | .0035 | .0037 | .0040 | .0045 | .0070 | .0090 |
| Cast Iron (hard) | 150–475 | .0018 | .0020 | .0025 | .0027 | .0030 | .0035 | .0040 | .0050 |
| Ductile Iron | 200–900 | .0020 | .0022 | .0025 | .0027 | .0030 | .0040 | .0050 | .0070 |
| Malleable Iron | 275–850 | .0020 | .0025 | .0030 | .0035 | .0040 | .0050 | .0060 | .0080 |
| Steels (P) | |||||||||
| Low Carbon Steels | 350–900 | .0020 | .0025 | .0030 | .0035 | .0040 | .0050 | .0060 | .0080 |
| Medium Carbon Steels | 200–675 | .0025 | .0026 | .0027 | .0028 | .0030 | .0040 | .0050 | .0060 |
| Steels Hardened to 35 Rc | 190–545 | .0020 | .0021 | .0022 | .0023 | .0025 | .0027 | .0030 | .0040 |
| Steels Hardened to 50 Rc | 90–275 | .0012 | .0012 | .0013 | .0014 | .0015 | .0026 | .0030 | .0035 |
| Mold Steels | 300–725 | .0020 | .0022 | .0025 | .0027 | .0030 | .0035 | .0040 | .0050 |
| Tool Steels | 175–525 | .0020 | .0022 | .0025 | .0027 | .0030 | .0035 | .0040 | .0050 |
| Stainless (M) | |||||||||
| Stainless Steels (soft) | 300–525 | .0020 | .0022 | .0025 | .0022 | .0030 | .0040 | .0050 | .0070 |
| Stainless Steels (hard) | 150–475 | .0015 | .0016 | .0017 | .0018 | .0020 | .0030 | .0040 | .0060 |
| Super alloys (S) | |||||||||
| Monel & High Nickel Steel | 75–250 | .0015 | .0022 | .0025 | .0027 | .0030 | .0035 | .0040 | .0050 |
| Titanium (soft) | 125–475 | .0015 | .0022 | .0025 | .0027 | .0030 | .0040 | .0050 | .0070 |
| Titanium (hard) | 50–195 | .0010 | .0016 | .0017 | .0018 | .0020 | .0022 | .0026 | .0030 |
| Nickel-Based High Temp Alloys | 50–175 | .0014 | .0014 | .0015 | .0016 | .0017 | .0018 | .0020 | .0023 |
For HEM toolpaths the chip load must be adjusted for radial chip thinning; enter your radial width of cut. If the tool runs well without vibration or noise, increase SFM and/or feed per tooth in 5–10% steps.
Aluminum
| Material | SFM Uncoated / ZrN / DLC | 1/4" | 5/16" | 3/8" | 7/16" | 1/2" | 5/8" | 3/4" | 1" |
|---|---|---|---|---|---|---|---|---|---|
| Feed per tooth (IPT) by diameter | |||||||||
| Non-ferrous (N) | |||||||||
| Aluminum & Aluminum Alloys | 900–1800 | .0030 | .0035 | .0040 | .0045 | .0050 | .0060 | .0070 | .0090 |
| Copper & Copper Alloys | 525–1275 | .0030 | .0035 | .0035 | .0040 | .0040 | .0045 | .0050 | .0070 |
| Brass & Bronze | 375–600 | .0030 | .0035 | .0035 | .0040 | .0040 | .0045 | .0050 | .0060 |
| Graphite | 500–1200 | .0040 | .0045 | .0045 | .0045 | .0045 | .0050 | .0060 | .0080 |
| Plastics | 600–1650 | .0040 | .0045 | .0050 | .0060 | .0070 | .0090 | .0110 | .0160 |
Depth of cut up to 1.5× diameter for profiling and 1× diameter for full slotting. If the tool runs well without vibration or noise, increase SFM and/or feed per tooth in 5–10% steps.